Best Selling Products

71609G01

607413 Steering Knuckle Component that Fits EZGO RXV Gas & Electric Golf Carts, Years 2008 & Up.

26814G01 The Snap Ring is a factory replacement for the axle bearing used in rear/Dana axle installations. This item fits on the end of the axle shaft. This snap ring prevents the bearing from moving and should only be used on vehicles with 4-Cycle transaxles, and a 295cc or 350cc Fuji-Robin Engine. This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

18488G1 The Silicon Rectifier Diode is used in the battery charger assembly to allow an electric current to flow uni-directionally and act as a semi-conductor in the battery chargers to regulate the electrical power in the vehicle. This diode should only be installed on 36V Powerwise, Powerwise +, Total Charge III, and Total Charger IV Chargers. Hardware is not included with this diode, 1/4" washer and 1/4-28" hex nut is needed. This itemreplaces previous Part#28548G01; and requires two (2) each as a replacementforone (1) 28548G01. This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

607462 Your gas golf car relies on spark plugs for keeping the vehicle running smoothly and efficiently. Spark plugs are responsible for "igniting" your vehicles air and fuel mixture within the combustion chamber. This NGK spark plug is of top quality and should be used on E-Z-GO Gas powered RXV and ST 4x4 Vehicles.

25864G09 Purchase your next golf cart controller from Shop.ezgo.com, your OEM source for genuine E-Z-GO parts and accessories. The speed controller is responsible for regulating the speed levels of your vehicle.This particular speed controlleris not designedfor use with DCS (Drive Control System) or PDS (Precision Drive System) vehicle applications. If you are looking to dial in better performance, than this electronic speed controller is for you. Vehicle Fit Used on 1994-current E-Z-GO Medalist and TXT 36-Volt Series Electric Vehicles (not forDCS or PDS) 2004-2012 MPT 800 1998-2002 Workhorse 800 Includes: Electronic Speed Controller Product Features/Information: Regulates the vehicles speed 250 Amp 36 Volt 5 Pin Genuine E-Z-GO Part

15113G1 The Snap Ring is a factory replacement axle bearing used in rear/Dana axle installations. This item fits on the end of the axle shaft. This snap ring cannot be used on RXV or MPT 1000 (Multi-Purpose Truck) Vehicles.

18287G1 This E-Z-GO Siphon Tube Assembly installs directly into the existing fuel tankand is used on E-Z-GO 2 & 4-Cycle Gas Golf Cars and Utility Vehicles. (NLA per J. Hundley - 1/29/16 r/b 18287G3) This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

614252 The vehicles Speed Sensor monitors the rotational direction of the Tyres to ensure the proper speed rotation of the wheel. This sensor is an OEM (Original Equipment Manufacturer) part that plugs into the speed sensor harness and should be installed on RXV Vehicles only.

25837G01 NLA per JBA 1/10/13 This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

26685G01 This spacer is for use with your E-Z-GO 4 Cycle Engine This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

26684G01 This spacer is for use with your E-Z-GO 4 Cycle Engine This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

73328G01 The Speed Sensor Magnet can be used with 48 Volt Advance motors for PDS II (Precision Drive System II) controllers. This sensor magnet ensures the desired signal strength is reached in order to determine the vehicles speed. This magnet can be used on 36V & 48V PDS (Precision Drive System)applications.

73327G01 This Speed Sensor determines the speed of the vehicle while in transit while also recording the rate in which the engines crankshaft is spinning. This particular speed sensor is used with (PDS)controllers and 48 Volt Advance motors for E-Z-GO Electric Vehicles.

25523G4 Your golf car relies on spark plugs for keeping the vehicle running smoothly and efficiently. Spark plugs are responsible for "igniting" your vehicles air and fuel mixture within the combustion chamber. This NGK spark plug is of top quality and should be used on E-Z-GO Vehicles with Pre-MCI & MCI Engines.

70931G01 This Spindle Assembly is manufactured for E-Z-GO Golf and Shuttle Vehicles with steering units that the steering housing is bolted directly on top of the axle (most January 2001-current vehicles). This assembly should be installed on the Drivers side. For the corresponding Spindle Assembly installed on the Passengers Side, please reference Part# 70930G01.

70267G02 This Spindle Assembly is a factory replacement part for E-Z-GO Gas & Electric TXT & Medalist Models. This item is manufactured for installment on the right side (Passengers side) of vehicle.

PF11512 Smart Linkfrom Pro-Fit provides real-time access for golf cart owners. The Smart Linksystem uses an easy to install device that attaches to the vehicle¡batteries and syncs to a mobile app. Monitor the battery level and remaining charging time when recharging. Receive real-time alerts when your golf cart needs attention. Explore real-time monitoring of battery and electrical data. Set customized alerts based on your preferences to gauge vehicle performance. The lockout feature allows you to easily secure your vehicle and prevent unauthorized theft without having to add any additional parts to the brake or wheel. The Smart Link Lockout Harness is sold separately and is available for your specific vehicle model. Includes: Smart Linkdevice, wiring harness, battery cable, bracket and hardware, and installation instructions. Golf Cart Compatibility: Club Car Precedent, Club Car DS, EZGO TXT (1996-Current), EZGO RXV, and Yamaha Drive golf carts. Mobile Device Requirements: iPhone 4S or newer or Android version 4.3 or newer is required to support Bluetooth® Smart technology. Download theSmart Link User Guide here. Download Smart Link Installation Instructions here. This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

70188G01 The Bearing Sleeve is a required component of the vehicles steering rack, bellows, and tensioner. This OEM(Original Equipment Manufacturer) replacement item should onlybe installed on the E-Z-GO Vehicles referenced. This is a Clearance Item, If sold out - Contact us for price and availability. No further discounting applies to Clearance Items.

70988G01 The Siphon Tube Grommet reinforces a hole in an apparatus and is required in heavy-duty applications that require durability. This grommet is usedon the vehicles siphon tube, Part# 73816G01, Siphon Tube.